How to do a Complete Brake Flush and Bleed
How to do a Complete Brake Flush and Bleed
How to Do a Brake Fluid Flush. Learn how to do a complete brake system flush to remove all of the old, water logged brake fluid out and replace it with fresh new DOT 3 brake fluid. I show you the two person method and the one person method to bleed the brakes. I also show you how to bleed drum brakes and disc brakes as well as the correct order to bleed them for a complete flush.
Here is the tubing you need for the brake bleeder: http://amzn.to/1RQyTyF
One Person Brake Bleeder: https://www.youtube.com/watch?v=1wwq1Vlk4Wg
Everything you Need to Know About Brake Fluid: COMING SOON
Wheel Cylinder Replacement: https://www.youtube.com/watch?v=GIWYkCOPAQ0
How to Replace Drum Brakes: https://www.youtube.com/watch?v=zJ_UXP6GWkw
**If the video was helpful, remember to give it a “thumbs up” and consider subscribing. New videos every Thursday**
-Subscribe Here: http://www.youtube.com/subscription_center?add_user=paintballoo7
-YouTube Channel: https://www.youtube.com/ChrisFix
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.
Remind just buy a car friend, first the new car factory not only has traveled limit, and the time limit, both to first go to so far.2;After the first of the normal maintenance is a bunch of spending. First said the oil change, we must first respect with the manufacturers use the standard, at least not lower than the standard factory. Such as selection of rating higher than standard oil producer, is can the appropriate extended use time, to filter the replacement of the also is same, machine and the oil is also change filter, the air filter is not necessarily, and using the environment related, such as the southern city or coastal cities, less air humidity dust. Can consider to use compressed air to clean up the then use, just as we wear a shirt, in the northern city of the along while collar is dirty, in the coastal city two days will not dirty, the truth is, can’t parrot. The fuel filter is the same, and use a fuel quality related, gasoline high quality not label high, label only represent the octane value of the gasoline or diesel oil hexadecane high value. Quality good fuel little impurity, steam fear can also be oil for the two to three oil period (10000-15000-km) change again. Not because the is small.Three; The cooling fluid (antifreeze) use and replacement, first the brand is different from the cooling liquid can’t mix and, for different brands cooling fluid additives is different, the practice has proved mixed with not only not protection after engines, but also easy to metal parts of the engine producing corrosion. Summer is same to use, the reason is cooling liquid boiling point of the high, average for 105-110 degrees, summer leaves air conditioning engine temperature will be on the high side, the use of coolant in special sections engine not “KaiGuo”, such as urban traffic, freezing point value detection is-8 °, winter in Beijing is not able to use, is based on test data change, also can’t parrot. The southern city of vehicle in use also can’t because the local environment to the high temperature and ignores the detection, especially in winter often drive north and south city to go back and forth friends are more should pay attention to.Four; The brake fluid (brake oil) and the use of replacement. And the cooling liquid, different brand can’t mix add! Mix and easy to have the similar after half a crystal turbidity content, make the brake efficiency is low. In total the brake pump oil storage cup on the brake fluid model or logo, for example DOT4, etc.Replace the premise is and use the time and place of the relevance is bigger, use of mostly is now synthetic brake fluid, and minerals or other brake fluid different, synthetic brake fluid in the braking effect has been greatly improved. The influence of rubber pieces of metal, plunger, the corrosion of the pump chamber has greatly improved. But the hygroscopicity relatively few stronger, is more sensitive to moisture from the air. Brake zongbeng of oil storage cup on design is normal pressure condition, and atmospheric interlinked, to the inevitable contact with air, the air of moisture blot within the brake fluid. Braking brake piece with brake disc because of the violent friction, produce the high temperature to brake fluid within the moisture to evaporate out, influence braking performance. Although there are vacuum booster, but beneath your backup camera feet brake pedal when also can feel not solid and slightly feeling elastic, exert the same dynamics, vehicle deceleration effect seems to be not satisfied. Change is to respect manufacturers the maintenance manual “request, unifies own use feeling and use areas, such as moisture in the south, and the north drying characteristics extended or shorten the time change.
Source: Free Articles from ArticlesFactory.com
ABOUT THE AUTHOR
Jodiemht has been in the car aftermarket industry for 3 years. She specializes in car camera , car GPS, car DVD player, car DVR and other aftermarket products. You can learn more about car DVD player and car GPS at her company site.